Phoenix Pro Quick Guide V2

1: 正面

2. Preparation & Vehicle Connection 2.1 Preparation 2.3 Vehicle Connection © The ignition is turned on. © The vehicle battery voltage is 9-18 volts. e The throttle is in the closed position. Phoenix Pro 1.OBD II Vehicle Connection Plug the VCI into the Vehicle's DLC port directly, or use the OBDII extension cable to connect the VCI with the Vehicle’s DLC port. There are two main components to the Phoenix Pro system: Phoenix Pro Display Tablet and VCI (Vehicle Communication Interface). 2.2 Working Principle 2. Non-OBD II Vehicle Connection For non-OBD II vehicle, proceed as follows: Vehicle's DLC port USB1 HDMI Port Port (For connecting it to charge the tablet via the USB cable) 1.

Locate vehicle's DLC port (refer to Section “VCI"). 2. Connect one end of the OBD | adaptor to the VCI, and the other end to the non-16 pin connector. (To connect an external projector or monitor with HDMI interface) USB2 Port 3. Plug the other end of the non-16pin connector into the DLC port. (To connect VCI, USB devices or add-on modules) 4. To supply power to the OBD | adaptor by one of the following DC-IN Jack (To connect the included power adaptor) ways: A. Via battery clamps cable (optional): Connect one end of the Reset Hole (To reset the tablet) ; } i EET =-—_—__———o @—— fle battery clamps cable to vehicle's battery, and the other end to the power jack of the OBD | adaptor.

oq cS ———e alco ey Se c—3 Memory Card Slot (To insert amemory card for memory extension.) Headphone Jack NS i Power/Screen Lock Key | vCl vo >| ae | Ethernet Port (To connect the crossover cable for wired network) Volume +/- Keys (To adjust the volume) | To Vehicle's DLC Port | on] Non-16pin Connector| am | OBD Adaptor | Ambient Light Sensor | To Vehicle's DLC Port vo] Non-16pin Connector| Microphone Phoenix Pro Tablet 5. If you choose to perform vehicle diagnosis via data cable, connect one end of the data cable into the VCI, and the other \l YUU UU y end into the USB2 port of the tablet. 3. Start Diagnostics afl Camera Flash e Intelligent Diagnostics:

® e @ °0®@ Tap “Local Diagnostics" step-by-step manual menu selection. Local Diagnostics: You need to manually select the menu-driven command. e e Rear Camera (Unfold the stand to a Vv certain angle to keep the tablet standing at your desk, or use it to hang the tablet on the driving wheel) Select vehicle model e Nr ¢ Adjustable Stand The system will automatically guide you directly to the fix and help you eliminate guesswork, without NNN For new users, the Local Diagnostics is recommended as follows: — Three diagnostic methods are available: ( Vv Audio Speaker ¢ Select software version Remote Diagnostics:

This helps repair shops or mechanics to diagnose a remote vehicle, and launch instant messages, Vv Select test system allowing for improved efficiency and faster repairs. IMPORTANT: Read the instruction carefully and use the unit properly before operating. and/or personal injury, which will void the product warranty. Vv Select test function * NOTE: This Quick Start Guide is subject to change without written. Fail to do so may cause damage

Page 1

页 3

Phoenix Pro T ablet VCI OBDII Extension Cable (A tablet for showin ( g test results.) (A device for accessing vehicle data.) To connect the VCI to the vehicle’s DLC port.) Power Adap tor Data Cable OBD I Adaptor (To supply power to the P (To connect the VCI and hoenix Pro Tablet.) Phoenix Pro to perform vehicle diagnosis.) (To supply power to the VCI through AC outlet.) Cigarette Lighter & Batter y Clamps Cable Password Envelope Adaptor Cable Kit AUD BEN BEN 98********00 BM CHR DAE DAI FIA r to the VCI FOR (A piece of paper with S/N and Activation ter, or the Battery GAZ Code, which is needed for your registration.) GM ble.) HO

Page 2