ROLAND — Back Cover

• The Advanced Edit Mode The TD-5 has an Advanced Edit Mode that is used to edit trigger parameters that are shared by all 32 patches. • Playing from Acoustic Drums (cont.) To trigger from acoustic drums: 1) Set the TD-5 to the Extended Edit Mode. 2) Hold the EDIT button until it begins to flash rapidly. 3) Strike the drum you wish to set. 4) Press PITCH, to select Trigger type, then press the PATCH buttons to select the appropriate trigger type: Kik, for kick drum; Snr, for snare; toM, for Toms; FLr, for floor tom. • To eliminate crosstalk between pads, press the REVERB > button to select crosstalk. Then, press the PATCH buttons to find the most desirable setting.

• To eliminate “false triggering,” press REVERB to select Mask Time. By pressing the PATCH > buttons, you can find the best setting. • To set the Scan Time, or length of time the trigger signal will be detected, press the REVERB TYPE buttons to set the value. • To eliminate erratic trigger waveforms or signals, press the REVERB TYPE > button. The PATCH buttons can be used to select the value. 1) To enter the Advanced Edit Mode, hold down the EDIT button until the LED begins to flash rapidly. 2) To select a trigger type, press PITCH press the PATCH buttons to select the appropriate trigger type. NOTE:

The TD-5 can recognize the PD-5, PD-7, PD-9 pads; the KD-7, and KD-5 kick pads, as well as a variety of other trigger types. In addition to pads, the TD-5 has settings for acoustic drum triggers. 3) To adjust the trigger sensitivity, press the PITCH > button. Use the PATCH buttons to change the setting. 4) To adjust the Threshold, press the DECAY, button. Use the Patch buttons to change the settings. 5) To set the Trigger Curve, press the DECAY >button. Use the PATCH buttons to change the setting. 6) Press EDIT to return to the Play Mode. • How to Send a Bulk Dump You can save all or part of the data in the TD-5 Percussion Sound Module to an external sequencer.

• Playing The TD-5 from Acoustic Drums The TD-5 can be triggered from acoustic drums with a transducer. The response time is a quick 3 ms and no additional attenuation is needed. When trigger- ing from acoustic drums, begin by setting the extended trigger parameters. 1) Connect the MIDI Out of the TD-5 to the MIDI In of the sequencer. 2) Hold down the EDIT button for a few seconds until the LED begins to flash rapidly. 3) Press the INSTRUMENT > button to select dnP, or Bulk Dump. 4) Use the PATCH buttons to select ALL, for all data in the TD-5, or 1 to 32 to save sound parameters for the selected patch. 5) Press the START/STOP button to begin sending the data.

6) Press the EDIT button to return to Play Mode. To access the extended trigger mode: 1) Hold down EDIT and PITCH power on. 2) Press the PATCH > button to on. This will put the TD-5 in extended edit mode. (Pressing the PATCH edit mode) 3) You must turn the power off and then on again to complete the procedure. Optional Accessories Include: FD-7 ..... Hi-Hat controller PD-5 ..... 8.5 inch single trigger pad* PD-7 ..... 7 inch dual trigger pad** PD-9 ..... 10 inch dual trigger pad** PD-100 . 10 inch single trigger V-Pad* PD-120 . 12 inch dual trigger V-Pad** KD-7 ..... Kick Trigger* FS-5U... footswitch for changing patches* NOTE: The TD-5 will remain in extended edit mode until turned off.

(* requires a mono 1/4 inch audio cable) (** requires a stereo 1/4 inch audio cable) TBS65 © Roland Corporation US, 7200 Dominion Circle, Los Angeles, CA 90040 Faxback # 20062 6/97 C@=2?5® ' A6C4FDD:@? D@F?5 >@5F=6