Supermicro SuperServer 1019S-M2 — 6.3 Advanced Setup Configurations

SuperServer 1019S-M2 User's Manual Chapter 6: BIOS Onboard LAN3 Option ROM Serial Port 1 Use this option to select the type of device installed in LAN Port3 used for system boot. The default setting for LAN3 Option ROM is Disabled . Select Enabled to enable the selected onboard serial port. The options are Enabled and Disabled. Onboard LAN4 Option ROM Logical Device Settings Use this option to select the type of device installed in LAN Port4 used for system boot. The default setting for LAN4 Option ROM is Disabled . This item displays the status of a serial part specified by the user.

Serial Port 1 Change Settings Onboard Video Option ROM This feature specifies the base I/O port address and the Interrupt Request address of a serial port specified by the user. Select Auto to allow the BIOS to automatically assign the base I/O and IRQ address. Use this feature to select which firmware type to be loaded for the onboard video controller. The options are Disabled, Legacy , and EFI. Network Stack The options for Serial Port 1 are Use Automatic Settings , (IO=3F8h; IRQ=4; DMA), (IO=3F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; DMA), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; DMA), (IO=3E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; DMA), and (IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; DMA).

Select Enabled to enable PXE (Preboot Execution Environment) or UEFI (Unified Extensible Firmware Interface) for network stack support. The options are Enabled and Disabled. IPv4 PXE Support Serial Port 2 Select Enabled to enable IPv4 PXE boot support. The options are Enabled and Disabled. Serial Port 2 Configuration IPv6 PXE Support This submenu allows the user the configure settings of Serial Port 1. Select Enabled to enable IPv6 PXE boot support. The options are Enabled and Disabled . PXE boot wait time Serial Port 2 Use this option to specify the wait time to press the ESC key to abort the PXE boot. Press "+" or "-" on your keyboard to change the value. The default setting is 0 .

Select Enabled to enable the selected onboard serial port. The options are Enabled and Disabled. Media detect count Logical Device Settings Use this option to specify the number of times media will be checked. Press "+" or "-" on your keyboard to change the value. The default setting is 1 . This item displays the status of a serial part specified by the user. Serial Port 2 Change Settings This feature specifies the base I/O port address and the Interrupt Request address of a serial port specified by the user. Select Auto to allow the BIOS to automatically assign the base I/O and IRQ address. Super IO Configuration The following Super IO information will display:

AMI SIO Driver Version The options for Serial Port 2 are Use Automatic Settings , (IO=2F8h; IRQ=3; DMA), (IO=3F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; DMA), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; DMA), (IO=3E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; DMA), and (IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; DMA). Super IO Chip Logical Device(s) Configuration Serial Port 1 Serial Port 2 Attribute (Available for Serial Port 2 only) Serial Port 1 Configuration Select SOL to use COM Port 2 as a Serial_Over_LAN (SOL) port for console redirection. The options are COM and SOL . This submenu allows the user the configure settings of Serial Port 1. 77 76