5011643500 032906

NET DVP-PF01 Installing the DVPPF01-S with the PLC controller Use a screwdriver to lift and unfasten the fixing clip. Open the extension cover with a screwdriver. ℃ ~55 ℃ EFT(IEC 61131-2, IEC 61000-4-4): Power Line: 2KV, Digital I/O: 1KV, Damped-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV ESD(IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge RS(IEC 61131-2, IEC 61000-4-3): 26MHz~1GHz, 10V/m ℃ ~70 ℃ (Temperature), 5~95% (Humidity) INSTALLATION AND CONFIGURATION 3 SPECIFICATION Standard: IEC1131-2, IEC 68-2-6 (TEST Fc) Message types DPV0, Cyclical data exchange process Analog & Communication I/O:

1KV IEC1131-2 & IEC 68-2-27 (TEST Ea) 2-wire twisted shielded cable DB9 9 pin connector High speed RS485 GSD file EATN09B9.GSD Electrical isolation 500V DC Device ID 09B9 HEX Model Name DVPPF01-S 9.6K bps 19.2K bps 93.75K bps 187.5K bps 500K bps 1.5M bps 3M bps 6M bps 12M bps Environmental Specifications Communication Baud rates (Auto detected) Noise Immunity http://www.delta.com.tw/industrialautomation/ 5011643500-PFE0 DVPPF01-S Profibus/DP Slave Adapter Instruction Sheet This is an OPEN TYPE Controller. The DVPPF01-S should be kept in an enclosure away from airborne dust, humidity, electric shock risk and vibration.

Also, it is equipped with protective methods such as some special tool or key to open the enclosure, so as to avoid the hazard to users or any damage to the module. Production week Production year (2005) Production plant (Taoyuan) Serial number of version Production Model 2006-02-20 This Instruction Sheet only provides descriptions for electrical specifications, general specifications, Production series • Support the SYNC and FREEZE for data synchronization between master and slaves. MA D E IN XX X XX X 4. Extension hole for mounting unit or module 8. Profibus connector Serial Number 1. Model name 2. Extension port 3. Power/NET LED 5. DIN rail clip 6. Extension clip 7.

Address switch 2 PRODUCT INTRODUCTION 24 Vdc 1.5W PF 01 -S 0 T54 000 01 Model Serial Number 1 WARNING • Cyclical data size is fixed to 4bytes input and 4bytes output. • Support GSD file configures by using configuration tools. For SS/SA/SX/SC MPU Do NOT touch terminals when power on. • Support 12MHz baud rate in DP network. „ Model Name and Serial Number Explanatoin: 6 7 8 6 • Cyclical data exchange process. • Support Auto Baud rate detection. Model name Power supply spec. Barcode & Series no. x16 1 0 x16 installation and wiring. „ Nameplate Explanation: PF: Profibus network module POWER POWER „ Product Profile NET DVP-PF01 „ Functions:

Product Series Model type Model number 4 3 2 1 4 5 3 SPECIFICATION Item Specification Interface DB9 9 pin connector Transfer method High speed RS485 Transfer cable 2-wire twisted shielded cable Electrical isolation 500V DC Message types DPV0, Cyclical data exchange process Device ID 09B9 HEX GSD file EATN09B9.GSD Model Name DVPPF01-S Baud rates (Auto detected) 9.6K bps 19.2K bps 93.75K bps 187.5K bps 500K bps 1.5M bps 3M bps 6M bps 12M bps Noise Immunity ESD(IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge EFT(IEC 61131-2, IEC 61000-4-4): Power Line: 2KV, Digital I/O: 1KV, Analog & Communication I/O: 1KV Damped-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV RS(IEC 61131-2, IEC 61000-4-3):

26MHz~1GHz, 10V/m Environment Operation: 0℃~55℃ (Temperature), 50~95% (Humidity), Pollution degree 2; Storage: -40℃~70℃ (Temperature), 5~95% (Humidity) Vibration / Shock Resistance Standard: IEC1131-2, IEC 68-2-6 (TEST Fc) IEC1131-2 & IEC 68-2-27 (TEST Ea) Approvals 1 DVP-PF01 4 5 x160 DVP-PF01 DVP-PF01

Page 1

PROFIBUS is an international, vendor- independent, opening filed bus standard for a wide range of applications in The PROFIBUS family comprises three types of protocol, PROFIBUS-DP, PROFIBUS-PA and PROFIBUS-FMS, PROFIBUS-PA (Process Automation): PROFIBUS-PA is the PROFIBUS solution for process automation, typically PROFIBUS-DP protocol for data transmission. It is designed to support intrinsically safe applications and can be used within hazardous areas, with high explosion risk using intrinsic safe MBP-IS interface. PROFIBUS-PA is used PROFIBUS-FMS (Fieldbus Message Specification): PROFIBUS-FMS is multiple master communications designed control equipment and cell-level controllers.

FMS services open up a wide range of applications and offer a wide the fields of manufacturing, production, process and building automation, and other automation control field. PROFIBUS-DP (Decentralized Periphery): PROFIBUS-DP is a rapid and low cost communication connection mainly designed for high-speed modem. PROFIBUS-DP has widespread usage for such items as remote I/O with MBP-IS transmission technology. Based upon PROFIBUS-DP, PROFIBUS-PA is an extension of the for communication at the cell level. It is designed for acyclic or cyclic data transfers at medium speed between systems, motor control centers, and variable speed drives.

It is designed and optimized especially for OFF Verify that ELC Controller is powered on. communication between automation systems and decentralized peripheral devices. LED Status Indication Corrective Actions LED Status Indication Corrective Actions Green ON No action needed. 6 APPENDIX – PROFIBUS-DP Green blinking Reserved No action. Green ON Cyclic data exchange in progress and OK No action. each of them is used for different tasks: to connect sensor and controller to the bus. range of functionality and flexibility.

Power LED PROFIBUS data are transmitted from DVPPF01-S module to Profibus-DP Master, it are mapping to Y20-Y57 in PLC controller This program example copies the 4 bytes data from X20-X57 that transmitted by DP master to D10 and D11 registers in PLC controller. And, PLC controller will write 4 bytes data in D20 and D21 registers to Y20-Y57, these 4 bytes data Verify that switch address setting match with configuration in DP master. DVPPF01-S provides fixed 4bytes input data and 4bytes output data to user in Profibus-DP system. 4bytes input when DVPPF01-S is the first extension unit of PLC.

4bytes output data are transmitted from Profibus-DP Master, Invalid PROFIBUS address Check whether the switch setting is valid. Setting range of slave: 1-125. Set the valid value and re-power. Verify that DP network installation is OK. Profibus network Verify DVPPF01-S is powered on. DVP-PS01 DVP-12SA DVP-PF01 Verify that PLC is working. Corrective Actions TROUBLESHOOTING DVP-PF01 Y0 C1 Y1 C2 Y2 Y3 RS-232 RS-485 Communication link to PROFIBUS, and No cyclical No action. MOV K4X20 D10 D11 K4Y20 D21 K4Y40 DVP-12SA 0 1 and it are also mapping to X20-X57 in PLC controller. K4X40 Red ON No connection to PROFIBUS D20 MOV MOV MOV Data Mapping:

Plug the PROFIBUS connector to the socket of DVPPF01-S, and tighten screw to secure the connector. The Maximum cable length in a segment depends on the transmission speed. PROFIBUS-DP communicates at Baud rate (bps) 9.6K 19.2K 93.75K 187.5K 500K 1.5M 3M 6M 12M Length (m) 1200 1200 1200 1000 400 200 100 100 100 Once connection is successful, software will check if 32 5 9 1 1 x16 0 x16 inputs/outputs is detected: 6 speeds from 9.6 Kbps to 12 Mbps over distances from 100 to 1,200 meters. Invalid PROFIBUS Address. NET LED will rapidly blink with RED when node address is at 0, 0x7E~ 0xFF.

3 RxD/TxD-P Data receiving/sending P (B) 5 DGND Data reference potential (C) 8 RxD/TxD-N Data receiving/sending N (A) 6 VP Positive voltage Check the extension I/O by WPL software: PIN Definition Content 1 .. 0x7D Valid PROFIBUS Address. Cable length and Baud rate PIN Definition of DP Connector 1 -- N/C 2 -- N/C 4 -- N/C 7 -- N/C 9 -- N/C Address Content Connect to PLC MPU: MAC ID Setting 0x7E .. 0xFF 0 or LED Status Indication Corrective Actions Green blinking Reserved No action. Green ON Cyclic data exchange in progress and OK No action. Green ON Power on No action needed. OFF No power Verify that ELC Controller is powered on.

Length (m) 1200 1200 1200 100 0 400 200 1 00 100 100 MOV K4X20 PIN Definition Content 1 -- N/C 2 -- N/C 3 RxD/TxD-P Data recei ving/sending P (B) 4 -- N/C 5 DGND Data refer ence potential (C) 6 VP Positive vo ltage 7 -- N/C 8 RxD/TxD-N Data recei ving/sending N (A) 9 -- N/C MOV D21 LED Status Indication Corrective Actions OFF No power supply Verify DVPPF01-S is powered on. Red blinking (rapidly) Invalid PROFIBUS address setting via switch Check whether the switch setting is valid. Setting range of slave: 1-125. Set the valid value and re-power. Red blinking Communication link to PROFIBUS, and No cyclica data exchanged l No action.

Red ON No connection to PROFIBU Verify that DP network installation is OK. Verify that PLC is working. S Verify that switch address setting match with configuration in DP master. Address Content 1 .. 0x7D Valid PROFIBUS Address. 0 or 0x7E .. 0xFF Invalid PROFIBUS Address. NET LED will rapidly blink with RED when node address is at 0, 0x7E~ 0xFF.

Page 2