LVS-7500 External System Installation and Quick Start Guide (EN)

LVS-7500 External System Installation and Quick Start Guide Copyright ©201 9 Omron Microscan Systems, Inc. Tel: +1.425.226.5700 / 800.762.1149 Fax: +1.425.226.8250 All rights reserved. The information contained herein is proprietary and is provided solely for the purpose of allowing customers to operate and/or service Omron Microscan- manufactured equipment and is not to be released, reproduced, or used for any other purpose without written permission of Omron Microscan . Throughout this manual, trademarked names might be used. We state herein that we are using the names to the benefit of the trademark owner, with no intention of infringement.

GS1 Solution Partner Disclaimer The information and specifications described in this manual are subject to change without notice. Latest Manual Version For the latest version of this manual, see the Download Center on our web site at: www.microscan.com . Technical Support For technical support, e-mail: helpdesk@microscan.com . Warranty For current warranty information, see: www.microscan.com/warranty . Omron Microscan Systems, Inc.

United States Corporate Headquarters +1.425.226.5700 / 800.762.1149 United States Northeast Technology Center +1.603.598.8400 / 800.468.9503 European Headquarters +31.172.423360 Asia Pacific Headquarters +65.6846.1214 LVS-7500 External System Installation and Quick Start Guide Page 2 of 45

Стр. 2

LVS-7500 External System Installation and Quick Start Guide Table of Contents Safety Instructions ......................................................................................................................... 4 Important Information .................................................................................................................... 4 Step 1: Installation Checklist ........................................................................................................ 5 Installation Checklist Images ....................................................................................................... 7 Step 2:

Install the LVS-7500 External System Software ............................................................. 8 Step 3: Assemble the LVS-7500 External System .................................................................... 28 Correct Placement Example ...................................................................................................... 34 Incorrect Placement Examples .................................................................................................. 35 Step 4: Install the Stop Motion Unit ........................................................................................... 38 Step 5:

Install the Light Tower Interface Unit (if purchased) ................................................... 40 Step 6: Log onto the LVS-7500 External System Software ...................................................... 42 Appendix A: Preventive Maintenance ........................................................................................ 43 Appendix B: LVS-7500 External System Stop Motion Unit and Light Tower Printer Interface44 LVS-7500 External System Installation and Quick Start Guide Page 3 of 45

Стр. 3

LVS-7500 External System Installation and Quick Start Guide Safety Instructions This unit has been carefully designed to provide years of safe, reliable performance. However, as with all electrical equipment, there are some basic precautions that you should follow to avoid personal injury or damage to the system:  Before using the system, carefully read all the installation and operating instructions.  Observe all warning instruction labels on the system.  To protect your system from overheating, make sure no openings on the system are blocked.  Never insert anything into the openings of the system.  Do not use the system near water or spill liquid into it.

 All components used to create your system are UL and CE approved. All circuits were designed to incorporate maximum safety. However, any equipment using electrical voltages may cause personal injury if improperly handled.  Do not attempt to work on the system with the main power lines connected.  Ensure that the AC power source matches the ratings listed for the system. If unsure, check with your dealer or local utility provider.  Do not place the AC power cord where it can be stepped on. If the AC power cord becomes damaged or frayed, replace it immediately.  Avoid looking directly into any system lights.

If you need to examine the lights, or look at any component near the lights, be sure to first turn off the lights. If the lights cannot be turned off, then wear polarized sunglasses while examining the lights.  To avoid damaging the system, turn off and unplug the system before cleaning.  If the system ever needs repair, consult Omron Microscan or your Omron Microscan distributor. Important Information  Due to continual product improvements, the product you receive may differ from the content outlined in this guide.

If you have questions about your product that are not covered in this guide, please contact your Omron Microscan representative or Omron Microscan headquarters at +1-800-762-1149 or helpdesk@microscan.com.  You MUST first install the LVS-7500 External System software BEFORE plugging in the LVS-7500 power cord or USB cable that connects the LVS-7500 External System and computer.  The LVS-7500 External System arrives to your site packaged in a specially designed cardboard shipping carton. DO NOT discard this shipping carton in case you must ship or store the system for any reason. Failure to use this carton when returning your product to Omron Microscan will void warranty.

 The LVS-7500 External System supports Windows® 7 Professional and Windows® 8.1 Professional.  If a USB device fails to load automatically, attempt to manually load the USB device using Device Manager. Consult your Systems Administrator for assistance, if required. LVS-7500 External System Installation and Quick Start Guide Page 4 of 45

Стр. 4

LVS-7500 External System Installation and Quick Start Guide Step 1: Installation Checklist The LVS-7500 External System and accompanying parts arrive in a cardboard shipping box. Carefully open the shipping box and locate each part within the foam support compartment. A list of each part is located below. Refer to the next section for a picture of each part. If any item is missing or damaged, contact your Omron Microscan representative for assistance.

 LVS-7500 External System installation flash drive (includes LVS-7500 software and “LVS-7500 External System Operations Manual”)  “LVS-7500 External System Installation and Quick Start Guide” (this document)  LVS-7500 External System Readhead (5.4”/137 mm) or (8.5”/216 mm)  Calibration Card (NIST Traceable)  Base Plate  Mounting Bracket with attached Internal Rewind Bar  Docking Plate  USB Cable 2.0 Certified (6 feet) (1.8 m)  Power Supply (5-Volt).

Requires localized power cord for shipments outside North America  AC Line Cord (for North American customers only)  Stop Motion Interface Unit (or Light Tower Interface Unit if purchased by customer)  5/32” Allen Key Optional Items  Light Tower Interface Unit. Replaces Stop Motion Unit. Provides color-coded warning lights to operator.  Motor-driven take up nip roll (designed for fan-fold)  Table-top label rewinder (winds up labels into a roll as they come out of a printer). Two available options:

o 1" to 4" (25.4 mm to 101.6 mm) Adjustable Core Holder o 8.6" (220 mm) wide "Quick-Chuck" and two label Flanges Customer-Supplied Items  Two screws (8-32 or M4) for Stop Motion Unit mounting  Two screws (8-32 or M4) for Light Tower Interface Unit mounting (if purchased)  Thermal Printer (if interfacing the LVS-7500 External System to the printer for stop motion capabilities, refer to the “Stop Motion Printer Interface Requirements” section below for important printer requirements)  Computer (see “Minimum Computer Requirements” below)  Internal or external rewind is required to properly feed the labels for inspection.

Lack of a rewind will remove any responsibility from Omron Microscan .  Mains power supply cable (for customers outside United States; this cable connects the power supply box to the wall power outlet) Minimum Computer Requirements  Intel® Core™ 2 Duo Processor or equivalent (Intel® Core™ 2 Quad is preferred)  2 GB RAM (4 GB is preferred)  80 GB Hard Drive (500 GB preferred) LVS-7500 External System Installation and Quick Start Guide Page 5 of 45

Стр. 5