NERLITE Smart Series DOAL Illuminator Configuration Guide (EN)

NERLITE Smart Series DOAL Illuminators Conf iguration guide Hardware Required 2 P/N 83-230018-02 Rev B Continuous Mode Continuous Mode With Dimming Or On-Off Control High Output Strobe Mode PART NUMBER DESCRIPTION Current Draw @ 24VDC (typ.) No Controller Required (Can Be Connected Directly To 24VDC) No Controller Required (Can Be Connected Directly To 24VDC) No Controller Required (Can Be Connected Directly To 24VDC) NER-011660400G SMART SERIES DOAL-25, RED .40A Figure A or D Figure B Figure C NER-011660410G SMART SERIES DOAL-25, WHITE .20A Figure A or D Figure B Figure C NER-011660420G SMART SERIES DOAL-25, BLUE .20A Figure A or D Figure B Figure C NER-011660500G SMART SERIES DOAL-50, RED 1.3A Figure A or D Figure B Figure C NER-011660510G SMART SERIES DOAL-50, WHITE 1.0A Figure A or D Figure B Figure C NER-011660520G SMART SERIES DOAL-50, BLUE 1.0A Figure A or D Figure B Figure C NER-011660600G SMART SERIES DOAL-75, RED 2.4A Figure A or D Figure B Figure C NER-011660610G SMART SERIES DOAL-75, WHITE 1.5A Figure A or D Figure B Figure C NER-011660620G SMART SERIES DOAL-75, BLUE 1.5A Figure A or D Figure B Figure C NER-011660700G SMART SERIES DOAL-100, RED 3.6A Figure A Figure B Figure C NER-011660710G SMART SERIES DOAL-100, WHITE 1.6A Figure A Figure B Figure C NER-011660720G SMART SERIES DOAL-100, BLUE 1.6A Figure A Figure B Figure C Item Description Part Number 1 Smart Series DOAL Lights NER-011660XXXG 2 Power Supply DSP60 24VDC 2.5A DIN Mount NER-011504100 2 Power Supply DSP100 24VDC 4.2A DIN Mount 97-000006-01 3 Cable 5 Pin M12 Female To Flying Leads, 3M 61-000186-01 3 Cable 5 Pin M12 Female To Flying Leads, 5M 61-000187-01 4 Cable, Power Smart Series to QX-1 61-000204-01

Стр. 1

NERLITE Smart Series DOAL Illuminators Accessories Connections Dimming Strobe Continuous On-Off Control Signals DIM (Continuous Mode With PWM Dimming): 0VDC (LEDs off) to 3.1-3.5VDC (LEDs on) pulse width modulated (PWM) signal , Note: When using Continuous Mode With Dimming, the LED duty cycle will equal the duty cycle of the dimming signal. DIM (Continuous Mode With On-Off Control): 0VDC (LEDs off), 3.1-3.5VDC (LEDs on), ( TRIG (High Output Strobe Mode): optoisolated, 0VDC (LEDs off) to 3.1-28.8VDC (LEDs on), 10mA max, 20 μs min Trigger pulse width. Note: High Output Strobe internally limits LED frequency and pulse width to a maximum of 90Hz and 1mS respectively.

Light output pulse will follow Trigger pulse width from 20 μs to 1ms. Note: When using Continuous Mode With Dimming, the LED duty cycle will equal the duty cycle of the dimming signal. Cable Specifications Wire colors for flying lead cables: Pin 1 = Brown Pin 2 = White Pin 3 = Blue Pin 4 = Black Pin 5 = Gray Connector Nut = Shield Note: Non-Omron Microscan cables may use different wire colors. It is the customer’s responsibility to make sure the light is connected correctly per the pin numbers in the table above. Copyright ©2019 Omron Microscan Systems, Inc.

www.microscan.com Description Part Number Application AC Power Cord US NER-030028300 Power Cord For Power Supply AC Power Cord EU NER-030028400 Power Cord For Power Supply AC Power Cord UK NER-030028500 Power Cord For Power Supply Input Connector (M12 Male, 5 Circuit, A-Code) Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Backshell Continuous Mode (Figures A & D): +20.2-28.8VDC DC GND DC GND +20.2-28.8VDC No Connection Shield Continuous Mode With Dimming (Figure B): +20.2-28.8VDC DC GND DC GND & DIM (-) +20.2-28.8VDC Dim (+) Shield Continuous Mode With On-Off Control (Figure B): +20.2-28.8VDC DC GND DC GND & DIM (-) +20.2-28.8VDC Dim (+) Shield High Output Strobe Mode (Figure C):

+20.2-28.8VDC TRIG (-) DC GND TRIG (+) No Connection Shield

Стр. 2