Phoenix — Owner's Manual — CAM 50Hz (EN)

4201 Lien Rd. • Madison, WI 53704 Owner’s Manual — Phoenix CAM 50Hz Installation, Operation & Service Instructions Read and Save These Instructions Low amp draw, balanced airflow characteristics and maximum velocity of 2700 FPM are what propel the Phoenix to rise above the competition. The unique 1/3 horsepower design of the Phoenix Centrifugal Air Mover, coupled with a two-speed switch, allows the restoration technician to deliver the most airflow using the fewest amps. Maximum amp draw on high speed is 2.0 amps. This drops to a mere 1.5 amps on low speed. It is now possible to fit as many as four Phoenix Centrifugal Air Movers onto a typical grounded circuit.

The Phoenix CAM is lightweight, has a power indicator lamp, large three-position switch, and superior cord management. The Phoenix housing is durable, washable, and chemical resistant. It features multiple operating positions allowing it to be angled up from horizontal to 45° and 90°. The Phoenix Centrifugal Air Mover • 2-Speed 1/3 Horsepower Motor 2.0 Amps on High Speed 1.5 Amps on Low Speed • Maximum Velocity of 2700 FPM (825 meters/min) • Balanced Exhaust Airflow • Directional Airflow Horizontal, 45° Angle, 90° Angle • Durable, rugged, chemical resistant housing, fan wheel, and controls design. • Operator interface conveniently located for easy access, featuring:

power indicator lamp and large three-position switch. • Phoenix exclusive Pilot Light and Sealed Switch are recessed to prevent damage. • Ergonomic carry handle and power cord storage. • Non-marking, anti-skid, rubber feet. Phoenix Centrifugal Air Mover 50Hz PN 4027620 Specifications subject to change without notice. TS-485 01/15 1 www.UsePhoenix.com • sales@UsePhoenix.com Toll-Free 1-800-533-7533

Стр. 1

Table of Contents Introduction ................................................................1 Centrifugal Air Mover Features and Benefits ...................1 1. Safety Information .................................................2 2. Specifications ........................................................3 3. Operating Instructions ............................................3 4. Operator Panel Features .........................................4 4.1 Power Indication Lamp.....................................4 4.2 3-Position Drying Selector Switch......................4 5.

Maintenance ..........................................................4 5.1 Servicing.........................................................4 5.2 Cleaning..........................................................4 6. Replacement Parts and Optional Accessories ...........4 7. Wiring Diagram ......................................................5 Warranty...............................................................6 1 Safety Information When using any rotational electrical device basic precautions should always be followed, including the following: CAUTION! For general ventilating use only. Do not use in environments containing hazardous or explosive materials and vapors.

• Do not operate the unit without the safety guards properly installed and secured. Do not operate the unit if the guards become damaged. Contact Therma-Stor for replacement parts. • Always replace the guards as originally installed after servicing or cleaning the product. • Never place your face, hands, or other susceptible body parts in the air stream, inlets, or outlet of this device. • This fan is not a toy! Ensure children do not play with and do not have access to the equipment. Do not allow children to play with or near the unit or in its air flow. • Do not use this fan with any solid-state speed control device. • Do not operate unit with a cut or frayed power cord.

Replace cord if it becomes damaged. • Handle with care. Do not drop or throw the unit. The unit can be damaged under harsh treatment. • Do not unplug the unit by pulling on the cord. Grasp the plug firmly and pull it out of the wall socket or power receptacle. • Always use a grounded outlet. • Never operate electrical equipment in standing water. • Never operate with the safety grills removed. Personal injury may result. • Do not stick your fingers or other objects through the safety grills. • Do not restrict airflow to the unit. This may cause the unit to overheat. • Unit should never be serviced or cleaned while it is plugged in.

• Make sure the unit is secure, stable and safe from falling over or falling down before operating. • Do not sit or stand on the unit or use as a shelf. • Do not leave device plugged in when not in use. • Indoor use only. Do not expose to water or rain–store indoors. • Use only as described in this manual. • Use only Manufacturer’s recommended attachments. Contact Therma-Stor for proper repair instructions. • Do not pull or carry it by the power cord, use cord as a handle, close doors on cord or pull cord around sharp edges.

Serial No.__________________________________ Purchase Date_____________________________ Dealer’s Name_____________________________ Read the operation and maintenance instructions carefully before using this unit. Proper adherence to these instructions is essential to obtain maximum benefit from your Phoenix 4027620. 2 www.UsePhoenix.com • sales@UsePhoenix.com Toll-Free 1-800-533-7533

Стр. 2

• Do not run over cord. • Keep cord away from heated surfaces. • Do not handle power cord plug with wet hands. • Turn off all controls before unplugging. • Do not use when you are tired, distracted or under the influence of drugs, alcohol or medication. 2 Specifications Part No. 4027620 Power 230 VAC, 50 hz. Operating 3 – 0°, 45°, 90° Positions Drive Motor 1 /3 Horsepower, 2-Speed LIRE ET CONSERVER CES INSTRUCTIONS Motor Thermal cut-off • Risque de choc йlectrique Peut causer des blessures ou la mort. Dйbrancher toutes les alimentations en courant йlectrique а distance avant l’entretien ou le nettoyage. • Ne pas utiliser l’appareil avec un cordon d’alimentation coupй ou effilochй.

• Ne pas dйbrancher l’appareil en tirant sur le cordon. Tenir la fiche fermement et la tirer hors de la prise murale ou la prise d’alimentation йlectrique. • Toujours utiliser une prise mise а la terre. • Ne jamais utiliser l’йquipement йlectrique dans de l’eau stagnante. • Ne jamais utiliser sans les grilles de protection. Des blessures risquent d’en rйsulter. • Ne pas brancher plus de 8 ampиres au total au diffйrentiel. • Vйrifier la protection du diffйrentiel avant chaque utilisation en appuyant sur le bouton “ test “. Si l’appareil fonctionne correctement, le bouton “ reset “ ressort. • Ne pas passer les doigts ou d’autres objets dans les grilles de protection.

• Ne pas diminuer le dйbit d’air arrivant jusqu’а l’appareil. L’appareil risque de trop chauffer. • Ne pas s’asseoir ou se tenir debout sur l’appareil; ne pas l’utiliser comme йtagиre ou table. • Avant de laisser un appareil aйraulique axial sans surveillance, s’assurer que les enfants n’ont pas accиs а l’йquipement. Ne pas laisser les enfants jouer avec l’appareil ou а proximitй de l’appareil ou dans l’air qu’il projette. • Pour rйduire le risque d’incendie ou de choc йlectrique, ne pas utiliser ce ventilateur avec un dispositif de commande de vitesse а semi-conducteurs.

Protection Cord Length 20 Feet Airflow 2700 ft/min outlet velocity Current Draw 2.0 Amps High speed, 1.5 Amps Low speed Warranty One Year - 100% parts and labor (all components) Three Years - Only materials and workmanship of the housing are covered. Dimensions Machine Shipping Width 17” 17.3” Height 20” Depth 19.4” Weight 26.5 lb 28 lb WARNING: The product is for household use only. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance. 3 Operation Instructions The Phoenix Centrifugal Air Mover is intended for use by water damage restoration, carpet cleaning, construction, and janitorial/sanitation professionals in general ventilating and structural surface drying applications. The Phoenix Centrifugal Air Mover as packaged is ready to be put into service. Inspect the unit completely for any shipping damage. Place the unit on the ground. Plug the unit into a grounded outlet and select the drying mode. 3 www.UsePhoenix.com • sales@UsePhoenix.com Toll-Free 1-800-533-7533

Стр. 3

4 Operator Panel Features 4.1 Power Indication Lamp The red, sealed, high intensity AC voltage power indication lamp allows operators to visually identify the operation status of several Phoenix Centrifugal Air Movers at a distance, with a single glance. The power indication lamp will remain lit when the AC power cord is plugged into a standard “powered” AC power outlet and the 3-Position drying selector switch is in either the HIGH or LOW operation position. The power indication lamp will remain unlit when the AC power cord is unplugged, the 3-Position drying selector switch in the OFF position, or the connected, standard AC wall outlet power has been turned off.

CORRECT DISPOSAL OF THIS PRODUCT: This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling 6 Replacement Parts and Optional Accessories 4.2 3-Position Drying Selector Switch The Phoenix Centrifugal Air Mover features a three-position switch - LOW–OFF–HIGH. 1.

Inspect the machine for damage and airflow Contact the factory at 1-800-533-7533 to order replacement parts, or optional accessories obstructions prior to plugging it in or operating it. 2. Ensure the power switch is in the OFF (middle) position. 3. Place the machine into the desired position for operation. Ensure that the machine rests stable and secure and will not overturn. 4. Turn the unit on to the desired speed, high or low. 5 Maintenance WARNING: Disconnect the unit from power before servicing or cleaning. Replace the safety grill after servicing, lubrication or cleaning.

5.1 Servicing Before each use, inspect for damage, blocked inlet or outlet, or any excess buildup of foreign material. When the Phoenix Centrifugal Air Mover is first turned on, check for excessive vibration. If the unit vibrates excessively or if blower wheel rubs on housing, turn off the unit immediately. Have a service technician inspect the unit to locate the problem. 5.2 Cleaning The housing is made of a durable and washable polyethylene. When cleaning, the use of solvents is NOT recommended. 4 www.UsePhoenix.com • sales@UsePhoenix.com Toll-Free 1-800-533-7533

Стр. 4