Tefal 1800110849 Steam Iron User Manual & Service Guide PDF (EN)

Please read these instructions carefully and keep for future reference. English ULTRAGLISS DIFFUSION 1800110849 - 23/07 Shot of steam button (depending on model) for removing wrinkles Spray Button to moisten linen Auto-Stop safety warning light (depending on model) Electric power cord Water tank filler cover Steam control Anti-calc valve To be cleaned once per month Spray Water tank maximum fill line Do not exceed this limit Sole plate Thermostat control For choosing the ironing temperature Thermostat indicator light Goes out when the temperature has been reached. Warning!

Before using your iron with the steam function for the first time, we recommend that you operate it in a horizontal position for a few moments, away from your linen, ie press several times on the shot of steam button WARNING ! Remove the sole plate protector before heating up the iron (depending on the model). During the first few uses, the harmless odour and smoke may be given off. This has no effect on the use of the iron and will disappear quickly. 1

Стр. 1

Your appliance has been designed to function with tap water. However, it is necessary to operate the Self-Clean function regularly in order to eliminate hard water deposits. If your water is very hard (check with your water authority), it is possible to mix tap water with store-bought demineralized water in the following proportions : 50% tap water, 50% demineralized water. What water to use ? Heat concentrates the elements contained in water during evaporation. The types of water listed below contain organic waste or mineral elements that can cause spitting, brown staining, or premature wear of the appliance:

water from clothes dryers, scented or softened water, water from refrigerators, batteries, or air conditioners, pure distilled water, or rain water. Types of water not to use : 1- STEAM IRONING Filling the water tank A B C D E F - Unplug your iron before filling it. - Set the steam control on DRY (A). - Fill the beaker up to the lower line indicated (B). - Open the water tank filler cover completely (C), set the iron on a table (not when the iron is hot) shown in the diagram (D) below, and fill the tank. - Do not exceed the MAX line indicated on the water tank (with the iron set on its heel). - Close the water tank filler cover.

- Set the temperature control shown in the diagram below (E) referring to the table below (or on the heel). - The thermostat light comes on.Wait for the light to go off and come on again before you start ironing (F). Setting the temperature Setting the steam level (G) 2 - In order to avoid water dripping from the iron onto the linen: Turn off the steam when ironing silk or synthetic fabrics. Set it at the minimum position for wool. G

Стр. 2

= STEAM ZONE SILK SYNTHETIC DRY DRY Polyester,Acetate,Acrylic, Nylon - When steam or dry ironing, press several times on the Spray Button to moisten the linen (H) and to remove stubborn creases. - Make sure that there is water in the tank before using this button. Moistening the linen (Spray) Recommendations: Fabrics and ironing temperatures: Your iron heats up quickly: begin by ironing those fabrics that are ironed at low temperatures, then go on to those requiring a higher temperature; If you turn down the thermostat, wait until the thermostat light comes back on before beginning to iron again.

When ironing fabrics with mixed fibres, set the ironing temperature for the most delicate of the fibres. H - Press the Shot of steam button from time to time (I). - Wait a few seconds between each shot before pressing the button again. Obtaining more steam for removing wrinkles (depending on the model) - Hang up the garment on a hanger and hold the fabric slightly taut with one hand. - Set the thermostat control on MAX (J). - Press the Shot of steam button ( )repeatedly (K), moving the iron from top to bottom (L). - Hold the iron a few centimetres from the fabric to avoid burning delicate fabrics.

Vertical steam ironing (depending on the model) I J K L 3 FABRIC POSITION OF THERMOSTAT CURSOR STEAM SETTING POSITION LINEN COTTON WOOL MAX ●●● ●● MAX MIN

Стр. 3

Auto-Stop safety feature (depending on the model) - The electronic system cuts off the electric power and the Auto-Stop warning light flashes if the iron is left vertically on its heel for more than 8 minutes, or in a horizontal position for more than 30 seconds. - To restart the iron, just move it gently until the warning light stops flashing. Note:When the Auto-Stop warning light is on, it is normal for the thermostat light to be off. M 2- DRY IRONING - Set the steam control on DRY (see diagram A). - Set the temperature. - You may start ironing when the thermostat light goes out and comes on again. 3- MAINTAINING YOUR IRON BE CAREFUL !

Unplug your iron and let it cool off before cleaning it. CLEANING THE ANTI-CALC VALVE (Once per month) : - Unplug your iron and empty the water tank. - To remove the anti-calc valve, pull it up using the tabs located on each side (N). NEVER TOUCH THE END OF THE VALVE. - Soak the rod in a cup of white spirit vinegar or plain lemon juice for 4 hours (O). - Rinse the valve in tap water. - Place the steam control on dry. - Replace the anti-scale valve. THE IRON WILL NOT FUNCTION WITHOUT THE ANTI-CALC VALVE N O USING THE SELF-CLEANING FUNCTION In order to extend the life of your iron, use the Self-Cleaning function once per month. - Unplug your iron and set the steam control on DRY .

- Fill the water tank up to the limit (see recommendations for the types of water to use). - Leave water tank filler cover open until the end of the operation - Place your iron on its heel and set the thermostat control on MAX. - Plug in your iron and wait until the thermostat light goes out. - Unplug the iron and hold it over a sink in the horizontal position. - Place the steam control on MAX. 4

Стр. 4