Print 603.93.431 Base - July 2006 Revi - June 2007 EUROCARGO EURO 4 - 5 FITTING SUPER STRUCTURES 3-47 Table 3.14 - Cranes mounted on rear overhang (subframe mounting with shear resistant plates) Total torque MG max (kNm) Model A x B x t (mm) 0/20 20/30 30/40 40/50 50/60 60/70 70/80 80/90 90/100 100/120 120/140 140/160 160/180 180/200 200/220 220/240 240/260 260/280 280/300 Minimum value of strength modulus of subframe section Wx (cm3) ML60, ML65, 172, 5x65x4 240 A A A 23 42 57 110 110 135 E ML75, ML80EL 360 A A A 23 32 57 110 110 135 E ML60, ML65, 172, 5x65x5 240 A A A 23 32 42 71 110 110 E ML75, ML80EL 360 A A A A 23 32 57 71 110 E ML80, ML90, ML100 195, 5x65x4 240 A A A A 32 42 71 110 110 E 360 A A A A 23 42 71 110 110 E ML80, ML90, ML100 195, 5x65x5 240 A A A A 23 42 42 71 110 135 E ML110EL*), ML120EL*) 360 A A A A A 23 32 57 71 110 E ML110EL*), ML120EL*) 195, 5x65x6 240 A A A A 32 57 71 110 110 173 E 360 A A A A A 32 42 57 71 110 135 E ML120, ML130, 240x70x5 240 A A A A A A 23 42 42 71 110 E ML150, ML100EW 360 A A A A A A A A 23 71 110 E ML120, ML130, ML150, ML140EW 240x70x6 240 A A A A A A A 32 42 71 110 135 E 360 A A A A A A A A 23 42 71 110 135 E ML120, ML130, 240x70x6, 7 240 A A A A A A A 23 42 57 110 135 E ML150 360 A A A A A A A A 23 32 57 71 110 135 ML150 240x70x7, 7 240 A A A A A A A 23 42 71 110 135 173 E 360 A A A A A A A A 23 32 57 57 110 135 173 E ML180 262, 5x80x6 240 A A A A A A 23 42 42 110 110 173 222 222 E 360 A A A A A A 23 23 23 42 71 110 173 222 246 246 E ML180 262, 5x80x6, 7 240 A A A A A A A 32 42 71 110 135 222 222 E 360 A A A A A A A 23 23 42 57 110 135 173 222 246 E ML180 262, 5x80x7, 7 240 A A A A A A A A 42 71 110 135 173 222 246 E 360 A A A A A A A A 23 32 42 71 110 135 173 222 222 246 E A = The reinforcing profile prescribed for the respective superstructure is sufficient (e.g.
table 3.1 for normal bodies). Close the reinforcing profile in the crane mounting area. In the crane area, the reinforcing profiles with thickness of less than 5 mm must be reinforced. E = To be checked on a case-by-case basis. Send the technical documentation with the checks of stresses and stability to the appropriate IVECO bodies. *) = On the MLL version, use a profile with strength modulus Wx of not less than 57 cm3.
If the height of the subframe profile has to be reduced, using shear resistant connections between chassis and subframe, combined section profiles can be used as shown in (see Table 3.15), instead of the C-profile, provided that the flange width and thickness are not less than the corresponding values of the profile indicated in Table 3.14. The above are general conditions which apply to the materials indicated. To assess whether it is possible to use materials with higher mechanical specifications, it is necessary to check the total resistant moment of the chassis plus subframe.
Since reducing the height of the subframe profile also reduces the torsion resistance, for cranes with four stabilisers, the bodybuilder must take special measures to ensure adequate torsional rigidity of the subframe in the crane mounting area. For this reason, it is recommended that you do not use profiles with a height of less than 120 mm.