Iveco — EuroCargo E4 BODYBUILDER INSTRUCTIONS

POWER TAKE-OFFS 4-15 E URO C ARGO E URO 4 - 5 The table below shows the parameters that, as a whole, constitute an EDC mode. The parameters can only be programmed using the E.A.SY. test tool available at IVECO Service. Note: The use of the MODUS station must take place after an upgrade is run using E.A.SY. software Table 4.5 Max No.

of revs Nmax (with engine not subjected to load) N LL ч 2700 (2) (3) (2500 rpm for E28 motors) Engine revs increase per second with SET+ 125 / 250 / 500 / 1000 rpm 125 / 250 / 500 / 1000 U/s Torque limitation (3 ) See Table Use of the CC buttons (Resume/OFF/SET+/SET-) Enabled / disabled TIP function, for SET+/SET- (4) Enabled / disabled Accelerator pedal Enabled / disabled Minimum N ° of revs that can be reached with SET-, NSET_min > 500 rpm > 500 rpm Maximum speed of the vehicle, above which PTO mode is enabled (intermediate speed rate V ZDR_max ) between 2 km/h and 95 km/h NLL Idling rpm N max Maximum rpm N res Stored rpm press Resume or activate PTO mode to recall N SET_max Maximum rpm achievable with SET+ button identical for all PTO modes N SET_min Minimum rpm achievable with SET (1) The reference speed is that of the crankshaft, not the PTO.

The corresponding PTO rpm must be calculated by means of the PTO reduction ratio. (2) The following rules refer to intermediate rpm ratio adjustment: - Never drop under the N LL value. - Never exceed the N max value. - In general N LL = N SET_min = N res and N res = N SET_max = N max . If the latter is not true, the engine rpm is limited to N max . (3) See para. 4.6.3.1. (4) The TIP function (i.e. brief pressure on SET+/SET- toggle button for speed regulator. The intermediate rpm regulator will be activated at speed 20 km/h. The speed variation of the intermediate rpm regulator steps are equal to 25 rpm for tip, which corresponds to 1 km/h for the speed regulator.

(5) Active the power take off mode is disengaged when the service brake or the clutch pedals are pressed. disabled the power take off mode is not disengaged when the service brake or the clutch pedals are pressed. In PTO mode 0, the power take off mode is disengaged when the service brake or the clutch pedals are pressed. (6) Active the power take off mode is disengaged when the parking brake or the clutch pedals are pressed. disabled the power take off mode is not disengaged when the parking brake or the clutch pedals are pressed. In PTO mode 0, the power take off mode is not disengaged when the parking brake is engaged.

(7) Active the engine goes automatically to the chosen Nres value for that power take off mode. disabled the engine remains at the previous rate, to reach the value Nres it is necessary to press the Resume button (pin 9 and 12 on the 20 pin connector). Abbreviations:

PTO management Print 603.93.431 Base - July 2006 Revi - June 2007 Parameter Possible values Maximum N° of revs that can be reached with SET+, NSET max _ NLL ÷ 2700 (2) (2500 rpm for E28 motors) Engine revs decrease per second with SET- As above Runaway speed regulator gradient ~2 / ~1 / ~0,65 CV / rpm (3) ~2 / ~1 / ~0,65 CV / rpm (3) Storing of intermediate speed rate Fixed (E.A.SY.)/free (driver) Exclusion of PTO mode using brake or clutch (5) Enabled / disabled Call-up intermediate speed rate stored with Resume on enabling PTO (7) Enabled / disabled Exclusion of PTO mode using parking brake (6) Enabled / disabled Possible power take-off rate range (1) NLL ÷ 2700 rpm (2) NLL ÷ 2700 rpm (2)