Seres user manual (EN)

Serial Number ............ ROUTER-RECREATOR SHOWN WITH SEARS ROUTER AND LEG SET Model and serial number may be found on a pfate attached to the yoke assembly. You should record both model and serial number in a safe place for future use. CAUTmON: ROUTER-RECREA TOR Read GENERAL and ADDITIONAL SAFETY .... ® assembly iNSTRUCTIONS ® operating carefully o repair parts Sold_by SEARS, ROEBUCK AND CO., Chicago, 1L. 60684 U.S.A. Part No. 76005

Стр. 1

This warranty g Yes you specif c egal rights, and you may also have other rights which vary from State to state; _ SEARSI ROEBUCK AND CO., DEPT. 69B/731A Sears ToWer. Chicago, IL 60684 Before =operating the Recreator read and understand your Router and Router Recreator owner's manuals and affixed warnings. The General Safety Instructions which follow apply to your Router and Router Recreator co mbinaUon as a "power tool." genera!l safety instructions for power tools 1. KNOW YOUR POWER TOOL Read and understand the owner's manual and 12. labels affixed to the tool Learn its application and limitations as well as the specific potential hazards peculiar to this tool. 2.

GROUND ALL TOOLS UNLESS USE SAFETY GOGGLES Safety goggles must comply with ANSI Z87.1-t968, Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have =mpact resistant lenses, they are not safety glasses. SECURE WORK Use clamps or a vise to hold work when practical, it's safe r than using your hand, frees both hands to operate toot. DOUBLE INSULATED 13. If tool is equipped with an approved 3-conductor cord and a 3--prong grounding type pug to fit the proper grounding type receptacle. The green conductor in the cord is the grounding wire. Never: connect the green 14. wire to a live terminal DON'T OVERREACH Keep proper footing and balance at all ttmes. 15.

MAINTAIN TOOLS WITH CARE Keep tools sharp and clean for best and safest performance. Follow instructions for lubrication and changing accessories. DISCONNECT TOOLS before servicing; when changing accessories Such as blades, bits, cutters, _tc. 3, KEEP GUARDS iN PLACE and in working order. 4. REMOVE ADJUSTING KEYS AND WRENCHES Form habit of checking to seethat keys and 16. adjusting wrenches are removed f,rom tool before tui'ning it on. : i :- : 5; KEEP WORK AREA CLEAN : 17. Cluttef;ed areas and benches nv te accidents. Ftoor must not be slippery dueto wax: or sawdust. --18. 6, AVOID DANGEROUS ENVIRONMENT Don't use power tools in damp or wet location. Keep work area well lit.

Provide adequate surrounding work space. 7. KEEP CHILDREN AWAY 19. AH visitors should be kept a safe distance from work area, 8. MAKE WORKSHOP KID-PROOF -- with padlocks, master switches, or by removing starter keys. 9. DON'T FORCE TOOL It wit! do the job better and safer at the rate for which it was designed. 10. USE RIGHT TOOL Don't force tool or attachment to d o a job it was not designed for. WEAR PROPER APPAREL No loose clothing, g oves, neckties or jewelry to get :caught in moving, parts. Rubber-soled damaged should footwear is recOmn_ended fop best footing replaced. AVOID ACCIDENTAL STARTING Make sure switch is in "OFF position before plugging in.

USERECOMMENDED ACCESSORIES Consult the owner's manual for recommended accessories. Follow the instructions that accompany the accessories. The use of tmprope_" accessories may cause hazards. NEVER STAND ON TOOL Serious injury could occur if the toot is tipped or if the cutting tool is accidentally contacted. Do not store materials above or near the tool such that it is necessary to stand on the tool to reach them. 20.

CHECK DAMAGED PARTS Before further use of the tool, a guard or other part that is damaged should be carefully checked to ensure that it will operate properly and perform its intended function, Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that as be properly repaired or

Стр. 2

additional safety instructions for router-recreator 1. ALWAYS USE EYE PROTECTION. The operation of any cutting tool can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear safety goggles complying with ANSI Z87.! before commencing cutting tool operation. We recommend Wide Vision Safety Mask for use over goggles.., available at Sears retail or catalog stores. 3. KEEP HANDS CLEAR OF BITS AND WORKING AREA. 4_ KEEP ROUTER RECREATOR AND ROUTER CLEAN After every use, clean saw dust off the Recreator and Router, 2. DON'T FORCE TOOL The Recreator was designed for smooth operation, therefore, parts should never be forced to operate. NOTE:

Motors used onwood-working tools are particularly susceptible to the accumulation of sawdust and wood chips and shouid be blown out or "vacuumed" frequently to prevent interference with normal motor ventilation. Note and follow the instructions found on the WARNING label which appears on the yoke assembly. WARNING FOR YOUR OWN SAFETY 1. READ AND UNDERSTAND OWNER'S MANUAL OF ROUTER RECREATOR AND ROUTER BEFORE OPERATING MACHINE. 2. WEAR SAFETY GOGGLES AND EAR PROTECTION. 3. DO NOT WEAR GLOVES, NECKTIE, OR LOOSE CLOTHING. TIE BACK LONG HAIR. 4. EXCEPT FOR SPINDLE WORK NEVER USE A SMALLER DIA. STYLUS TiP THAN THE CUTTER. 5. BE POSITIVE YOU DO NOT RUN CUTTER INTO C-CLAMPS.

WEAR YOUR The operation of any power tool can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear safety goggles complying with ANSI Z87,1 (shown on Package) before commencing power tool operation. Safety Goggles are available at Sears retail or catalog stores. CONTENTS General Safety Instructions ................ 2 Additional Safety Instructions ............. 3 Introduction .. : ........................ 4 Unpacking and Checking Contents .......... 4 Getting to Know Your Router-Recreator ..... 4 Assembly .............................. 5 Base Assembly ....................... 5 Yoke Assembly .......................

7 Cable Assemblies ...................... 8 Instaliing the Router ................... 9 Installation of the Counterweight ......... 1! Installing the Pulley Guards ............. 12 Mounting Your Router-Recreator to a Stand. !2 Alignment ............................. !3 Operation ............................. 15 Genera! Operating Hints ................ 15 Three Dimensional Carving .............. 16 2O Sign Making ......................... Decorative Edging ..................... 22 Spindle Decorating ................... 23 Recommended Accessories ............... 25 26 Repair Parts ...........................

Стр. 3

ntroduchon Thank :you for- the purchase of your, Router and more enjoyable operatiOn later, Recreator we think 0neof the most exciting and "tart b " '- :' - " "; " " - _ ,:_,_ ,_ __L__ ..,:_:n._ i" ":"r _ _ y cnect_ ng anQ accoun[ ng mr all the loose creaEivetuon_ w G,,)llle.alU g H yed =. --arts If an -art " ; " ";" " : .... .... . : p . yp s are missing cnecK me car_on once In order tofaclitate;handlingand.minimiZe any more, then contact your local Sears Retail or damage that might occur during shipment your new Catalog outlet for replacement. Recreator s packaged un-assembled We know Th . . T . .... :

" "t J- b t e model number or your Recreator (113 251890) youreanxloustoseewnatyournew_oolwtl oo u an-" th ...... ............ '- .... n: w areful readn the u upar_numDeroTmemlssmgpar_wi Devery a Tew minutes spe t no , c y g het-fu n ............. fo low ng instructions, wi 1 result in less frustration p s_€;ur_ng _ne replacemem part. unpacking and checking contents ITEM DESCRIPTION QTY. A Corner Brackets ........................ 2 A 8 C _, D E B Track Brackets ......................... 2 h A , _ | C Pulley Cover Guards ................... 2 1_ t Y /7 _ _ * E She f Boards .......................... 4 ii/i_iii._j _2 P.c -- _,_'_"_ % X G 1/16 ' styIUSRR_d ............... ........

11 Sii___ J Yoke Assembly .. ........ : .............. _ i _ r=_ I i _ t L Pulleys (5") ............................ 21 L K H \G F M Counterweight Shaft .. ........ .......... N Counterweight ......................... 1 P Shaft Lock Brackets .................... 2 K Shaft .................. ; ............... 1 N' _ V _K J _\ _ ITEM DESCRIPTION QTY. Q Loose Parts Bags ....................... 2 Collar .................................. 2 Bag. No, 76008 contains the following: Cable ................................... 2 Spindle Center Screw .................... 2 Stylus Mount ........................... 1 Large Knob ........................... 1 Small Knob ...; ........................

1 3/4" Stylus Collar ...................... 1 Stylus Grip .... ......................... I Screw, Soc. Set 1/4-20 x 1/4 ............. 4 Nut. Hex 8-32 .......................... 2 Washer 3/16 x 3/8 x 1/32 ............... 2 Screw, Seres Pan Hd, 10-32 x 3/4 ...... 2 Lockwasher_ External 1/4 .............. 2 Screw, Soc. Set 5/16-18 x 5/16 .......... 1 Screw. Hex Hd 3/8-16 Ч 1-1/2 .......... 2 Washer. 3/8 x 7/8 x 5/64 ................ 2 Bag NO. 76018 contains the _otlowing: Screw. Pan, Hd. t/4-20 x1-1/,_..... ..... : 20 Nut. Hex Jam 3/8-16 .................... 6 Wrench. Hex "L" t/8 .................... 1 Wrench, Hex "L" 5/32 .................. 1 Screw, Rd. Hd. 1/4-20 x 2-1/2 ...........

1 Screw, Pan lid 10-32 x 1/2 .............. 3 Screw Pan Hd t/4-20 x 1/2 ........... 18 Nut, Hex 1/4-20 . . ......... ....... _ 32 Wing Nut. 1/4-20 ....................... 2 getting to know your router-recreator COUNTER YOKE ASSEMBLY WEIGHT TILT PLATE ROUTER MOUNT / We'll be referring to the various parts of the Router Recreator by name throughout this manual• It will be helpful if you study the following drawing and familiarize yourself with the major components, Periodic referral to this section will also be helpful if you become puzzled while reading some of the more detailed instructions. l FRONT CORNER SHELF BOARD . BRACKET INNER PULLEY COVER " : -:

SHELF BOARDS _ GUARDS i CORNER TRACK BRACKET " 4

Стр. 4